Apet pet sheet is used more and more in the continuous development of society. Some cosmetics industry, food industry, electronic toy industry use APET sheet wholesale more and more. APET sheet wholesale itself also has many choices and uses. In fact, there are many ways to use APET sheet wholesale waste. This time, Fullstar plastic sheet roll manufacturers briefly talked about how to reuse APET sheet.However, in the process of extruding APET sheets, and even the subsequent thermoforming of APET sheets, waste sheets will inevitably be generated. Reusing these sheets usually encounters the following problems:The irregular size and low volume density of Plastic APET sheets material can easily cause blockage of the conveying system;In the drying hopper, the drying air in the opposite direction to the flow of the APET sheet material will interfere with the material flow;When granulating with APET flakes, particles are produced.In this regard, the solution is as follows:Reduce the size of the APET sheet rolls to avoid blockage of the suction tube and weaken the interference of the dry air on the material flow;Adjust the volume of dry air to match the output of the drying system;The sharpness and clearance of the granulator blade are the key factors for the generation of particles, so the blade should be kept sharp, and the gap between the rotor blade and the fixed blade should be as small as possible.Furthermore : The glass transition temperature of APET starts at approximately 180 ° F (82.2 ° C), depending on its composition. When heated to the glass transition temperature, APET begins to soften, melt and agglomerate, which will cause the material to stop flowing in the drying hopper, so before drying at high temperature, the APET waste sheet must be crystallized!APET sheet wholesale is used more and more in the constant demand of society. Reasonable choice and use become more and more important. The society is constantly changing. The demand is increasing. How to reuse APET sheet waste is a good resource recycling.

APET sheet is used in many industries, we should all know this! In our lives, many products are made using APET sheets! I don't know how much you know about such a sheet? In fact, do you know that it has good insulation performance? If you don't understand, you can follow our APET sheet wholesaler to know it!Insulation performance of APET sheet:1. Because the melting point of PP sheet is relatively high and it is a semi-crystalline material, the benefits of APET sheet will be more prominent and the advantages will be more obvious. 2. Clear apet sheet has good insulation performance, little influence by temperature, but poor corona resistance. Dongji PET film is non-toxic, weather-resistant, chemical-resistant and stable, has low water absorption, and is resistant to weak acids and organic solvents, but it is not immersed in hot water and alkali-resistant. 3. PET rigid sheet can be added with different additives according to different uses, and PVC plastic can exhibit different physical properties and mechanical properties. APET sheet can be made into a variety of hard, soft and transparent products by adding an appropriate amount of plasticizer to PVC resin. 4. After PVC and additives are mixed and plasticized, the PVC sheet is made into a transparent or colored film with a specified thickness using a three-roller or four-roller calender, and the film is processed by this method to become a rolled film.We have introduced here the insulation advantages of apet pet sheett! If you have any need for our products, you can call us!

APET sheet is made of PET material.Various plastic sheets is widely used in industry. There are also hundreds of plastic sheets. APET plastic sheet is the one that stands out because of its very characteristics Stable, and there are many advantages in use, so today let APET sheet wholesale manufacturers talk about the advantages of APET sheet.1. Light specific gravity: PET specific gravity 1.33 is 3.7% lower than PVC specific gravity 1.38     2. High strength: PET film is more than 20% stronger than PVC film, and has better low temperature impact resistance. It can withstand -40 ° C without brittleness, so it is usually replaced by 10% thinner film.     3. Good folding resistance. PET film does not have self-cracking creases like PVC, and is more suitable for surface decoration such as documents.     4. PET film has high transparency (PVC film is bluish), especially the gloss is better than PVC film, and it is more suitable for exquisite packaging.Clear APET plastic sheet is widely used and has good effect. It is a very popular sheet now. APET sheet is also very environmentally friendly, not only in the electronics industry, but also in cosmetics, food, toys, printing and other industries. With its figure, it is a good choice for high-end packaging. If you need APET sheet wholesale, please feel free to call us.

PET anti-fog film is used to prevent fogging. It is widely used in many aspects. With this product, we can enter a warmer place in winter without causing water on the mirror Fogging phenomenon such as beads, do you know where the advantages of PET anti-fog sheet in production?1. It has good mechanical properties, the impact strength is 3 to 5 times that of other films, and the folding resistance is good, so there is no need to worry about folding easy to break.2. Anti-fog PET sheet is resistant to oil, fat, dilute acid and alkali, and resistant to most solvents.3. PET anti-fog sheet has high transparency, can block ultraviolet rays, and has good gloss.4. PET anti-fog sheet has low permeability to gas and water vapor, so it can block water vapor well, not light, and has excellent gas barrier, water, oil and odor properties.5. PET anti-fog sheet has good resistance to high and low temperature, and can survive in the bad environment of -70 ~ 150 ℃, but it will be relatively long at 120 °, and it will exist in 150 ° for a long time. It is relatively short, and its mechanical properties are little affected at high and low temperatures.The above are the advantages of Fullstar Anti fog PET sheet manufacturers. If necessary, we can contact our manufacturers. The manufacturers specialize in the production and development of plastic materials such as APET, PVC, PETG, PP, HIPS,GAG, etc. The products are environmentally friendly It is safe and medical grade. We operate APET sheet wholesale and GAG sheet production. Please call us if you need it.

Last week, propylene's external disk rose sharply and then fell back, while the domestic market stabilized and fell slightly. Recently, there is still a slight upward trend in the domestic PP sheet market, but the transaction is average, and the atmosphere of speculation is relatively strong. It can be seen from the figure that the prices of some products in the extruded polypropylene sheet market in Beijing continued to increase slightly in recent days. At the same time, other market offers have also risen significantly. Most products have an increase of 100-200 RMB. The domestic PP sheet market price is still rising slightly Last week, the PP sheet market experienced a callback, but near the weekend, crude oil prices rebounded sharply again, driving the plastic market to rise rapidly. Common in all marketsDomestic PP sheet market prices are still slightly upLast week, the vacuum forming pp sheet  market experienced a callback, but near the weekend, crude oil prices rebounded sharply again, driving the plastic market to rise rapidly. The general mentality of the markets around the world has improved, and offers have increased. At present, petrochemical stocks are gradually reduced, and the pressure of goods delivery is not large. The downstream operating rate has increased compared with before, and it is mainly to wait and see to meet the rigid demand. The market trend of the PP sheet market still maintained its upward trend. The spot market was affected by the parking of devices such as Fulian and Maoming. The resources in some areas of southern China were tight, and the prices of the supporting prices were firm.The offer of Hebei PP sheet roll market was higher; the offer of Nanjing PP sheet market rose, and traders took the opportunity to speculate more; the offer of Shenyang PP market continued to increase, and the inquiry was acceptable; the offer of Shanghai PP sheet market rose; Qilu Chemical The city PP market continues to rise, the inquiry atmosphere is light, and the transaction is average; the price of the Beijing PP market is up, and the transaction is profitable; Active follow-up and actual order negotiation; Changzhou PP sheet market offer increased; Chengdu PP sheet market price increased and transactions made profit; Hangzhou PP sheet market offer increased.

APET Sheet:l Name: Amorphous polyethylene terephthalate l  Description :  1) Thickness:0.15-2.0mm               2) Width: 1100mm Max               3) Weight: 50-150kg/rolll  Density:1.34g/cm³l  Packaging:In roll or sheetsl  Criticaltemperature: 1) Heat deflection temperature: 78℃2) Coldresistance temperature: -5℃- -10℃3)Melting temperature: 265℃-280℃.l Type: Vacuum forming, Antistatic, Folding box, Open window,Antifogging, Printing, Metallizing film etc.l Application:Food packaging, Cosmetics box,Electronic packing, Stationery, Blister, Handware, Credit card, Shirt collar,Tape for printing, Coated label etc.l Feature: Excellent transparency and glossy, Lowerdensity, Less crystal point,Resistance to grease & acid & chemicaldrug, Excellent toughness, High impact resistance, Good vacuum formation andbody smoothness, High-quality folding & painting effect, High gas battier,Non-toxic & odourless & tasteless, Non-pollution.Comparewith pvc film, APET has the following advantages:1. Light weight: The density of APET (1.33g/cm³)is 37% lower than that of PVC (1.38g/cm³).2. High strength: PET films is 20% stronger thanPET film, Better shock resistance at low temperature, Don’t rattle at -40℃, Normally 10% thiner APET replace ofPVC film.3. Good folding resistance, don’t appear cracklike PVC film, be more suitable for decoration like file.4. Hig transparency (PVC is bluish),its gloss isbetter than PVC,More suitable for exquisite packaging APET thick plate:●  Feature: Non-pollution, Excellent transparency and glossy, Non-crystal point, Highimpact resistance, Good physical and chemical properties, Good machinability,Bad weather resistance. Non-toxic and harmless.●  Application:Advertising material, Frames binding, Building roof, Transparent outdoorprotection cover, Protection cover of Light box, Advertising board of bus stop,Product display rack, etc. It can replace of PMMA and PS board.●  Speficitation:1)      Thickness:0.80 - 2.00 mm2)      Size: I) 915mm*1220mm          II) 915mm*1830m